PRD Stainless Steel Header Bolts

Probesport · May 3rd, 2005, 02:25 PM

$14.84

Fits: 2.5l & 1.8l V6 Mazda motors found in the Ford Probe, Mazda MX6, 626 & MX3

These automotive grade stainless steel header bolts are perfect for your factory manifolds, aftermarket headers or custom turbo setups. Each kit contains enough hardware to do the front & rear banks completely. Included are the SS bolts and SS lock washers to ensure a tight fit & seal every time.

Don't put those rusted out factory fasteners back on your engine again!

unknowncitizen · May 4th, 2005, 01:54 AM

what size are these?

Probe 2C · May 4th, 2005, 05:29 AM

Quote:

Originally Posted by unknowncitizen

what size are these?

The same size as oem

Probesport · May 4th, 2005, 06:28 AM

Quote:

Originally Posted by unknowncitizen

what size are these?

Quote:

Originally Posted by Probe 2C

The same size as oem

Pretty much. The benefit of being in the motor city, and actually KNOWING one of the biggest automotive bolt suppliers in the world lends me a bit of an advantage. I stop by give them a bolt and say "I want these, stainless and by the case" I stop by later that week and I pick them up. Thats pretty much about it.

I could get the actual size/pitch/length for you, but that would be work - and I don't like that

j/k I will ask next time I am up there.

ctmx6 · May 4th, 2005, 10:17 AM

can you get them for the 2.0? i would love new hardware for my new header. thanks

Probesport · May 4th, 2005, 10:19 AM

Quote:

Originally Posted by ctmx6

can you get them for the 2.0? i would love new hardware for my new header. thanks

If you have an manifold/header bolt you can send me I can get them for the 2.0 guys.

pgtfreak · May 4th, 2005, 11:42 AM

Replacing the studs/nuts as well? If so, add some of these to my parts box

Probesport · May 4th, 2005, 11:44 AM

Quote:

Originally Posted by pgtfreak

Replacing the studs/nuts as well? If so, add some of these to my parts box

Yes this set would replace the studs/nuts. I only use bolts now, it makes installation a bit easier as well

Da-ze · May 5th, 2005, 04:38 PM

the important question..

what grade of SS are they?

heat over time seems to fatigue cheaper stainless... = broken bolt

I hate broken bolts..

95PGTTech · May 5th, 2005, 04:49 PM

got a paypal...I was just talking to ARP about some, ooh pricey!

95PGTTech · May 5th, 2005, 04:57 PM

btw they're listed as 14.84 on the site...

Probesport · May 5th, 2005, 05:46 PM

Quote:

Originally Posted by 95PGTTech

btw they're listed as 14.84 on the site...

Yeah I put them on special

Quote:

Originally Posted by 95PGTTech

got a paypal...I was just talking to ARP about some, ooh pricey!

Cool - will go out tomorrow.

Quote:

Originally Posted by Da-ze

the important question..

what grade of SS are they?

heat over time seems to fatigue cheaper stainless... = broken bolt

I hate broken bolts..

A2-70, reccomended for exhaust bolts by a tier 2 supplier

MonoxideChild · May 5th, 2005, 11:51 PM

how about 1st gens exhaust manifold studs and nuts?

s8n · May 9th, 2005, 12:37 AM

Sexy, I've been meaning to buy some PRD products for a while. Too bad I'm a poor bastard, but going through the site there's a few large items I want, not to mention small ones such as this and the other lil' goodies you have on there

Probesport · May 9th, 2005, 08:03 AM

Quote:

Originally Posted by xxxmonoxidechil

how about 1st gens exhaust manifold studs and nuts?

I cant get stainless studs on a consistent basis here but I could do "all bolt" kits.

Quote:

Originally Posted by s8n

Sexy, I've been meaning to buy some PRD products for a while. Too bad I'm a poor bastard, but going through the site there's a few large items I want, not to mention small ones such as this and the other lil' goodies you have on there

Thanks for the compliments!

ctmx6 · May 9th, 2005, 05:17 PM

what is the difference between studs and bolts? also, annny chance you can get some for the 2.0 without well...my help because I cant spare to send you one of mine. thanks, Rory

95PGTTech · May 9th, 2005, 05:59 PM

hey guys, just got my bolts in the mail, that was quick.

they look great, although the packaging wasn't too professional. brown paper lunch bag?

great seller, seems like a great product, we'll see once I get them installed

Probesport · May 9th, 2005, 07:00 PM

Quote:

Originally Posted by ctmx6

what is the difference between studs and bolts? also, annny chance you can get some for the 2.0 without well...my help because I cant spare to send you one of mine. thanks, Rory

I will look into 2.0 bolts, studs are threaded rods you put nuts on.

Quote:

Originally Posted by 95PGTTech

hey guys, just got my bolts in the mail, that was quick.

they look great, although the packaging wasn't too professional. brown paper lunch bag?

great seller, seems like a great product, we'll see once I get them installed

If you would like, I can jump up the pricing a bit and get custom wrapping for everything

Honestly, the paper is there to stop the bolts from clanging around during shipping.

I appreciate your comments on the shipping, I am glad we finally have enough people involved to provide proper service to everyone, fast shipping is oen of my biggest achievments so far

95PGTTech · May 9th, 2005, 07:15 PM

Quote:

Originally Posted by Probesport

I will look into 2.0 bolts, studs are threaded rods you put nuts on.

If you would like, I can jump up the pricing a bit and get custom wrapping for everything

Honestly, the paper is there to stop the bolts from clanging around during shipping.

I appreciate your comments on the shipping, I am glad we finally have enough people involved to provide proper service to everyone, fast shipping is oen of my biggest achievments so far

can that be JDM carbon fiber custom wrapping that has huge logos of your company name all over it?

I was joking about the packaging, it got it here in one piece.

Da-ze · May 18th, 2005, 09:12 AM

Quote:

Originally Posted by Probesport

Yeah I put them on special

Cool - will go out tomorrow.

A2-70, reccomended for exhaust bolts by a tier 2 supplier

http://www.google.com/search?q=A2-70...Steel&hl=en&lr=

Amazing stuff!!

Nice work Ken!

leading SS grade used by the industry standard..

Probesport · May 18th, 2005, 09:26 AM

Thanks, we try to do as much research as we can when we put something on the market which is why sometimes it takes a little longer to get things out there, but when we do - they are right

xtreme2 · May 2nd, 2006, 09:15 AM

hey Ken, I just did a motor swap, so i have the extra bolts that the stock header came attached with. If you PM me your address I can send you one so you can get the 2.0L bolts done...

Probesport · May 2nd, 2006, 09:49 AM

Absolutely, PM me if you need the address. You will get a free stainless set in replacement for yours.

May 3rd, 2005, 02:25 PM	#1
Probesport Authorized PT Vendorator Join Date: Feb 2000 Location: Sprawling on the fringes of the city Posts: 18,238	PRD Stainless Steel Header Bolts $14.84 Fits: 2.5l & 1.8l V6 Mazda motors found in the Ford Probe, Mazda MX6, 626 & MX3 These automotive grade stainless steel header bolts are perfect for your factory manifolds, aftermarket headers or custom turbo setups. Each kit contains enough hardware to do the front & rear banks completely. Included are the SS bolts and SS lock washers to ensure a tight fit & seal every time. Don't put those rusted out factory fasteners back on your engine again! __________________ Some will sell their dreams for small desires, or lose the race to rats. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. - The original Ford Probe Aftermarket 1999-2010 : over 10 Years of supporting the Probe community *To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.* Last edited by Probesport; May 5th, 2005 at 05:44 PM.

May 4th, 2005, 01:54 AM	#2
unknowncitizen Donating Member Join Date: Jan 2004 Location: Las Vegas, NV Age: 25 Posts: 3,876	what size are these? __________________ *To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.* ~GREDDY~MAGNAFLOW~ACT FIDANZA~WILWOOD~AWR~RR-RACING~HS~OUTLAW PRD~MSD-WINDOWS~TEIN-SS~RX-8~ALPINE

May 4th, 2005, 11:42 AM	#7
pgtfreak A legend in my spare time Join Date: Feb 2000 Location: an imaginary place where black rims don't exist Age: 30 Posts: 27,560	Replacing the studs/nuts as well? If so, add some of these to my parts box __________________ To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

May 5th, 2005, 11:51 PM	#13
MonoxideChild POC Mod Join Date: Jul 2002 Location: RockFord, IL. ChiPoC Age: 30 Posts: 12,236	how about 1st gens exhaust manifold studs and nuts? __________________ PaTricK To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. ~ 89 PLx, 92PgT. 88 colt GTS turbo, 90 FE3 626 GT hatch, 05 Mazda6, 09 Kia Sportage 4x4 v6 ~ To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

May 9th, 2005, 12:37 AM	#14
s8n Senior Member Join Date: Jan 2003 Location: Encinitas, CA Age: 28 Posts: 3,064	Sexy, I've been meaning to buy some PRD products for a while. Too bad I'm a poor bastard, but going through the site there's a few large items I want, not to mention small ones such as this and the other lil' goodies you have on there __________________ '93 Rio Red PGT - Dead and in the garage To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. '93 Silver PGT - Temperamental and heavily modified '07 Black A4 - A turbo, exhaust gasses go into the turbocharger and spin it, witchcraft happens and you go faster.

May 4th, 2005, 10:17 AM	#5
ctmx6 PT Regular Join Date: Nov 2003 Posts: 790	can you get them for the 2.0? i would love new hardware for my new header. thanks

May 5th, 2005, 04:38 PM	#9
Da-ze Balls Across The Nose Join Date: Oct 2002 Location: PA Age: 27 Posts: 2,191	the important question.. what grade of SS are they? heat over time seems to fatigue cheaper stainless... = broken bolt I hate broken bolts..

May 5th, 2005, 04:49 PM	#10
95PGTTech Push The Limits Join Date: Jul 2004 Location: Levittown, PA Age: 25 Posts: 6,956	got a paypal...I was just talking to ARP about some, ooh pricey!

May 5th, 2005, 04:57 PM	#11
95PGTTech Push The Limits Join Date: Jul 2004 Location: Levittown, PA Age: 25 Posts: 6,956	btw they're listed as 14.84 on the site...

May 9th, 2005, 05:17 PM	#16
ctmx6 PT Regular Join Date: Nov 2003 Posts: 790	what is the difference between studs and bolts? also, annny chance you can get some for the 2.0 without well...my help because I cant spare to send you one of mine. thanks, Rory

May 9th, 2005, 05:59 PM	#17
95PGTTech Push The Limits Join Date: Jul 2004 Location: Levittown, PA Age: 25 Posts: 6,956	hey guys, just got my bolts in the mail, that was quick. they look great, although the packaging wasn't too professional. brown paper lunch bag? great seller, seems like a great product, we'll see once I get them installed

May 18th, 2005, 09:26 AM	#21
Probesport Authorized PT Vendorator Join Date: Feb 2000 Location: Sprawling on the fringes of the city Posts: 18,238	Thanks, we try to do as much research as we can when we put something on the market which is why sometimes it takes a little longer to get things out there, but when we do - they are right __________________ Some will sell their dreams for small desires, or lose the race to rats. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. - The original Ford Probe Aftermarket 1999-2010 : over 10 Years of supporting the Probe community *To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.*

May 2nd, 2006, 09:15 AM	#22
xtreme2 BATN, but aka: DLSpeed_Inc. Join Date: Oct 2003 Posts: 2,510	hey Ken, I just did a motor swap, so i have the extra bolts that the stock header came attached with. If you PM me your address I can send you one so you can get the 2.0L bolts done...

May 2nd, 2006, 09:49 AM	#23
Probesport Authorized PT Vendorator Join Date: Feb 2000 Location: Sprawling on the fringes of the city Posts: 18,238	Absolutely, PM me if you need the address. You will get a free stainless set in replacement for yours. __________________ Some will sell their dreams for small desires, or lose the race to rats. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. - The original Ford Probe Aftermarket 1999-2010 : over 10 Years of supporting the Probe community *To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.*