If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
Complete KLZE Engine
Centre Air vents
Driver Air vent
Front wheel mud guards/plastic wheel arches
Wheel arch engine guards left and right
Passenger door trim
Driver seat or 2 x MX6 front seats
Rear seat top and bottom
Full cabin carpet in good condition
Top front dash plastic piece, the long rear piece right up near windscreen
Pretty much nobody left here in the Aus section, id find a wrecker or for that much stuff you would be better off going to an auction and buying a whole car. I don't have any of that stuff sorry.
Pretty much nobody left here in the Aus section, id find a wrecker or for that much stuff you would be better off going to an auction and buying a whole car. I don't have any of that stuff sorry.
yeah. I figured nobody has them down here anymore wreckers are hit and miss, they send you garbage.
Im just looking for a set of KLZE pistons or equivalent. no luck so far
Not sure what equivalent compares with ZE pistons?
I have a set of OEM NEW KL-DE pistons, rings and rods (no big end bearings) . I removed them from a new unused short block when I went with a set of KJ-ZEM rods and hi comp pistons. They are sitting here looking for a good home.I advertised them recently on Trademe.co.nz. Lots of watchers but no bidders.
Chris
Eunos Presso HI-XS Special Edition, KLZE, KL47 IM+TB, MX6 LSD box OEM front s/bar, Outlaw IM+TB thermalbloks, lightened K801 fly, XTD Stage 3 clutch & cover balanced to f/wheel, mbolin tranny saver , walbro 255,short shifter, SRD shifter bushings- H&R Springs and Koni inserts, MSpeed engine mounts, SS brake and clutch lines, PRM CAI,Whiteline rear strut and swaybar, 7x17 Konig/Maxxim Fourteen rims, and stuff.
.
Not sure what equivalent compares with ZE pistons?
I have a set of OEM NEW KL-DE pistons, rings and rods (no big end bearings) . I removed them from a new unused short block when I went with a set of KJ-ZEM rods and hi comp pistons. They are sitting here looking for a good home.I advertised them recently on Trademe.co.nz. Lots of watchers but no bidders.
Chris
Equivalent would be having the same compression ratio as the ZE pistons. 10.1:1
Complete KLZE Engine
Centre Air vents
Driver Air vent
Front wheel mud guards/plastic wheel arches
Wheel arch engine guards left and right
Passenger door trim
Driver seat or 2 x MX6 front seats
Rear seat top and bottom
Full cabin carpet in good condition
Top front dash plastic piece, the long rear piece right up near windscreen
Thanks.
Not sure if my being in Victoria helps, but
I found a complete 1995 Probe in White at Pick-a-part in Melbourne recently. It may still be in their Campbellfield yard, but I'm not sure if they will remove and ship parts to you. It did have immaculate carpet in it, but the driver's side seat was worn out at the bolster as usual. I took the distributor off of the engine and the front bumper was removed as well.
Also, EKW in East Keilor may have a complete KLZE engine (I got mine from them a few years ago).
Good luck
As a matter of fact, I do know everything. What I choose to disclose is at my discretion.
Due to front end damage Im now deciding to part out my 1995 Mazda 626 Deluxe Hatch rather than fix the radiator support bar. Someone with the time or skill could restore this easily enough but with a bigger family priorities have changed.
Some of the items fitted:
Digital Climate Control
BC Coilovers
Upgraded Mazda 6 Front Brakes
Full Leather Interior.
V6 Manual.
Msg me crobson69 At gmail.com or phone me 0447 714 208
Anyone after any ford probe parts in Australia i have parted mine out and have tons of parts left including but not limited to:
5 speed manual trans
alternator with freewheeling pulley (never fitted)
catch can
radiator overflow tank
1/4 panels
rear 1/4 glass
rear valve cover
Comment