The new hot-ness... slow as death, but hopefully next year that will change - Page 6

KLDE Wagon · October 21st, 2009, 11:04 AM

3.73's will be fine. I'll get decent gas mileage and I should only be hitting 3rd in the 1/4 mile.

Jeremy

KLDE Wagon · October 22nd, 2009, 10:23 AM

Just talked to the guy, picking it up tomorrow! It's gonna be nice to have the insurance of knowing I'm not gonna bust my rear when I'm leaving the line... That alone is worth $75

Plus this rear is upgradable to 31 spline axles and a 5 lug if I eventually decide do ditch the Pony wheels and get some centerlines

Jeremy

KLDE Wagon · October 29th, 2009, 10:09 AM

If everything goes to plan I will have a garage this winter to work on her

I'm wicked excited cause I really want to have it boosted by spring and not have to wait. I have the rear end now so I won't be afraid to get on it a little out of the hole with some boost, plus it should do nice two wheel smokeys

Jeremy

riithunder916 · October 29th, 2009, 10:24 AM

Awesome!!! I would definatly plan on a 5 lug swap! Otherwise you should be good to go! Boost her right up!!

KLDE Wagon · October 29th, 2009, 10:30 AM

When I get some extra money and can afford to get a nice set of 5 lug wheels... And get the minitub so I can fit some fatties under it

Jeremy

Loafff · October 29th, 2009, 11:30 AM

WOODGRAIN!. Put some 20's on it. lol

riithunder916 · October 29th, 2009, 12:11 PM

Lol 20's would be OVERKILL....a good set of fd's would look nice..or the cobra r's. I agree with the tubbin, you need to get more rubber under her to make her go go go.

KLDE Wagon · October 29th, 2009, 11:49 PM

275's fit stock... I'm looking more for the 315+ variety though

Jeremy

riithunder916 · October 30th, 2009, 09:31 AM

damnnn!!!!!!!!

So your looking for some WiDe tires then!! well, 12" wide should be more than enough to handle that power!!

lol

KLDE Wagon · October 30th, 2009, 09:34 AM

Yes sir... What's the sense in having a rear wheel drive if you don't stuff fatties under it??

I'm going to go wide in the front too, cause I want the car to handle. Proabably go with a 235 or so. It has 225's on the Pony wheels now but with the soft springs up front they rub if I turn and hit a bump like pulling into a driveway and such.

http://www.jegs.com/i/Centerline/184/135106545/10002/-1 These are probably what I'll run for wheels. I like this car with 5 stars. I might even look into some Torque thrusts but everyone runs them...

Jeremy

riithunder916 · October 30th, 2009, 09:37 AM

I wouldn't go past an 8" wide front, with either 10 or 12 out back!! I myself am putting 10" wides on my 74 charger, just going with a stickier rubber!!

KLDE Wagon · October 30th, 2009, 09:51 AM

I want to make a statement with this car lol It's gonna be virtually stock outside with a couple custom touches but I want the perfect stance and I want everyone to be able to see if my oil pan is leaking when I leave the line

Jeremy

riithunder916 · October 30th, 2009, 09:58 AM

lol!! I know the feeling!!

Last weeknd I was at the track with my friends 71 road runner. 440 big block bored .30" over with dual 800 cfm carbs and a bunch of head work. he pulls 11 second quarters, and well you can inspect not only the engine, but the floor pan too when he leaves the line!!!

Mike

KLDE Wagon · October 30th, 2009, 11:36 AM

Here is essentially the same car as mine, a 79 fairmont. It mostly just has different body panels but I believe it is an early fox platform. It could be a small block or a big block, it's hard to say as I didn't see under the hood. All I saw was the bottle in the back.

Jeremy

TRWeiss1 · October 30th, 2009, 12:31 PM

FAIL! The video is unavailable...please try again later.

Jeremy you're gonna need a considerable amount of power to pull the front tires off the ground significantly...I'll believe it when I sees it!

KLDE Wagon · October 30th, 2009, 10:58 PM

Check it again douche-fag!

True, but the fact of the matter is I have the chassis to do so... I'm not talking fast and the furious wheelies cause damn, who wants to not see a big rig pull out in front of you!!

Jeremy

riithunder916 · November 1st, 2009, 08:06 PM

Nice!!! it sounds like a small block to me.....

Mike

KLDE Wagon · November 2nd, 2009, 10:24 AM

Yeah, I would imagine so too. I just wish mine was as clean as that

mines a rust bucket... Anyones grandma have a car like mine sitting in her garage? HAHA

Jeremy

KLDE Wagon · November 9th, 2009, 09:13 AM

Garage is cleaned out (kinda). Enough to bring my car up and rip shit apart. I hope this wiring isn't too much of a nightmare.

Jeremy

riithunder916 · November 9th, 2009, 09:25 AM

LOL, well I hope it isn't to bad either!! wiring can be a Pain, but luckily in 85 things weren't too complicated!!

KLDE Wagon · November 9th, 2009, 09:29 AM

Exactly!! However I am rewiring the entire dash and essentially the whole car

. Gonna be lots of head scratching but then again I had lots of that on my KL swap too

Bought the stronger tensioner springs for the supercharger belts so when I up the boost they won't slip. The price was right and it was something I would eventually need and can use even running stock boost. I can't wait to take the dash all out, rip out the old motor and trans and start prepping to bolt the new one in!!!

Jeremy

KLDE Wagon · November 16th, 2009, 09:47 AM

The car is at my buddies, might start tearing into it this weekend

I got a cherry picker too now but it needs some TLC. I need to get working on the dash wiring a bit before I worry too much about getting the stock motor out, so that's first.

I discovered this morning that the headers I bought for $85 shipped are the $400 ones for the 3.8, and not Paceshitter

Jeremy

P.S. I did a line lock before pulling it into the garage too

once I get his camera I'll post the one-wheel-wonder before video

riithunder916 · November 16th, 2009, 10:20 AM

Nice!! I'm glad you got the good headers!

Mike

KLDE Wagon · November 16th, 2009, 10:32 AM

They are a little beat up but IDC LOL if they sound good and make power that's all I care about!! I can't wait to get the damn thing running!

Jeremy

KLDE Wagon · November 21st, 2009, 04:37 PM

Welp folks, it's been a while... Here are a couple of pics of the stock motor and of my hurst pistol grip shifter

http://i793.photobucket.com/albums/y...s/IMG_0665.jpg 130HP of FURY!!!

http://i793.photobucket.com/albums/y...s/IMG_0666.jpg
http://i793.photobucket.com/albums/y...s/IMG_0667.jpg

I'll try to get the video of this beast burning rubber from my buddy tomorrow

Jeremy

October 21st, 2009, 11:04 AM	#126
KLDE Wagon Supercharged Member Join Date: Aug 2006 Location: Binghamton, NY Age: 22 Posts: 1,200	3.73's will be fine. I'll get decent gas mileage and I should only be hitting 3rd in the 1/4 mile. Jeremy __________________ To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. 05 Mazda 3s: lighting mods and wheels To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. : 3" body lift, 35's, cammed, full exhaust Back to terrorize with drift-eze... Eventually To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

October 22nd, 2009, 10:23 AM	#127
KLDE Wagon Supercharged Member Join Date: Aug 2006 Location: Binghamton, NY Age: 22 Posts: 1,200	Just talked to the guy, picking it up tomorrow! It's gonna be nice to have the insurance of knowing I'm not gonna bust my rear when I'm leaving the line... That alone is worth $75 Plus this rear is upgradable to 31 spline axles and a 5 lug if I eventually decide do ditch the Pony wheels and get some centerlines Jeremy __________________ To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. 05 Mazda 3s: lighting mods and wheels To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. : 3" body lift, 35's, cammed, full exhaust Back to terrorize with drift-eze... Eventually To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. Last edited by KLDE Wagon; October 22nd, 2009 at 10:25 AM.

October 29th, 2009, 10:09 AM	#128
KLDE Wagon Supercharged Member Join Date: Aug 2006 Location: Binghamton, NY Age: 22 Posts: 1,200	If everything goes to plan I will have a garage this winter to work on her I'm wicked excited cause I really want to have it boosted by spring and not have to wait. I have the rear end now so I won't be afraid to get on it a little out of the hole with some boost, plus it should do nice two wheel smokeys Jeremy __________________ To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. 05 Mazda 3s: lighting mods and wheels To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. : 3" body lift, 35's, cammed, full exhaust Back to terrorize with drift-eze... Eventually To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

October 29th, 2009, 10:24 AM	#129
riithunder916 Juiced Member Join Date: Mar 2006 Location: West Greenwich RI Age: 22 Posts: 925	Awesome!!! I would definatly plan on a 5 lug swap! Otherwise you should be good to go! Boost her right up!! __________________ 2004 Nissan Sentra Ser Spec-V ==> daily 1987 T-bird T-coupe ===> 2.3 Turbo charged project To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

October 29th, 2009, 10:30 AM	#130
KLDE Wagon Supercharged Member Join Date: Aug 2006 Location: Binghamton, NY Age: 22 Posts: 1,200	When I get some extra money and can afford to get a nice set of 5 lug wheels... And get the minitub so I can fit some fatties under it Jeremy __________________ To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. 05 Mazda 3s: lighting mods and wheels To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. : 3" body lift, 35's, cammed, full exhaust Back to terrorize with drift-eze... Eventually To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

October 29th, 2009, 11:30 AM	#131
Loafff Member Join Date: Oct 2008 Location: Surrey, BC Age: 23 Posts: 172	WOODGRAIN!. Put some 20's on it. lol __________________ 94 PGT-ZE--K-Sports--Rota Grids w/ KDW's--Mach 1 lip--Powdercoated valvecovers/fuel rails/intake mani--Headers--CAI--95 Tails--Euro Gauge Cluster--Full Leather--1 Piece Panels

October 29th, 2009, 12:11 PM	#132
riithunder916 Juiced Member Join Date: Mar 2006 Location: West Greenwich RI Age: 22 Posts: 925	Lol 20's would be OVERKILL....a good set of fd's would look nice..or the cobra r's. I agree with the tubbin, you need to get more rubber under her to make her go go go. __________________ 2004 Nissan Sentra Ser Spec-V ==> daily 1987 T-bird T-coupe ===> 2.3 Turbo charged project To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

October 29th, 2009, 11:49 PM	#133
KLDE Wagon Supercharged Member Join Date: Aug 2006 Location: Binghamton, NY Age: 22 Posts: 1,200	275's fit stock... I'm looking more for the 315+ variety though Jeremy __________________ To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. 05 Mazda 3s: lighting mods and wheels To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. : 3" body lift, 35's, cammed, full exhaust Back to terrorize with drift-eze... Eventually To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

October 30th, 2009, 09:31 AM	#134
riithunder916 Juiced Member Join Date: Mar 2006 Location: West Greenwich RI Age: 22 Posts: 925	damnnn!!!!!!!! So your looking for some WiDe tires then!! well, 12" wide should be more than enough to handle that power!! lol __________________ 2004 Nissan Sentra Ser Spec-V ==> daily 1987 T-bird T-coupe ===> 2.3 Turbo charged project To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

October 30th, 2009, 09:34 AM	#135
KLDE Wagon Supercharged Member Join Date: Aug 2006 Location: Binghamton, NY Age: 22 Posts: 1,200	Yes sir... What's the sense in having a rear wheel drive if you don't stuff fatties under it?? I'm going to go wide in the front too, cause I want the car to handle. Proabably go with a 235 or so. It has 225's on the Pony wheels now but with the soft springs up front they rub if I turn and hit a bump like pulling into a driveway and such. http://www.jegs.com/i/Centerline/184/135106545/10002/-1 These are probably what I'll run for wheels. I like this car with 5 stars. I might even look into some Torque thrusts but everyone runs them... Jeremy __________________ To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. 05 Mazda 3s: lighting mods and wheels To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. : 3" body lift, 35's, cammed, full exhaust Back to terrorize with drift-eze... Eventually To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. Last edited by KLDE Wagon; October 30th, 2009 at 09:37 AM.

October 30th, 2009, 09:37 AM	#136
riithunder916 Juiced Member Join Date: Mar 2006 Location: West Greenwich RI Age: 22 Posts: 925	I wouldn't go past an 8" wide front, with either 10 or 12 out back!! I myself am putting 10" wides on my 74 charger, just going with a stickier rubber!! __________________ 2004 Nissan Sentra Ser Spec-V ==> daily 1987 T-bird T-coupe ===> 2.3 Turbo charged project To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

October 30th, 2009, 09:51 AM	#137
KLDE Wagon Supercharged Member Join Date: Aug 2006 Location: Binghamton, NY Age: 22 Posts: 1,200	I want to make a statement with this car lol It's gonna be virtually stock outside with a couple custom touches but I want the perfect stance and I want everyone to be able to see if my oil pan is leaking when I leave the line Jeremy __________________ To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. 05 Mazda 3s: lighting mods and wheels To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. : 3" body lift, 35's, cammed, full exhaust Back to terrorize with drift-eze... Eventually To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

October 30th, 2009, 09:58 AM	#138
riithunder916 Juiced Member Join Date: Mar 2006 Location: West Greenwich RI Age: 22 Posts: 925	lol!! I know the feeling!! Last weeknd I was at the track with my friends 71 road runner. 440 big block bored .30" over with dual 800 cfm carbs and a bunch of head work. he pulls 11 second quarters, and well you can inspect not only the engine, but the floor pan too when he leaves the line!!! Mike __________________ 2004 Nissan Sentra Ser Spec-V ==> daily 1987 T-bird T-coupe ===> 2.3 Turbo charged project To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

October 30th, 2009, 11:36 AM	#139
KLDE Wagon Supercharged Member Join Date: Aug 2006 Location: Binghamton, NY Age: 22 Posts: 1,200	Here is essentially the same car as mine, a 79 fairmont. It mostly just has different body panels but I believe it is an early fox platform. It could be a small block or a big block, it's hard to say as I didn't see under the hood. All I saw was the bottle in the back. Jeremy __________________ To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. 05 Mazda 3s: lighting mods and wheels To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. : 3" body lift, 35's, cammed, full exhaust Back to terrorize with drift-eze... Eventually To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

October 30th, 2009, 12:31 PM	#140
TRWeiss1 Donating Member Join Date: Jul 2002 Location: Squirting all over Binghamton, NY! Age: 28 Posts: 10,644	FAIL! The video is unavailable...please try again later. Jeremy you're gonna need a considerable amount of power to pull the front tires off the ground significantly...I'll believe it when I sees it! __________________ 95 PGT MTX - Probezilla - Supercharged 'n Squirted ZE @ 8 psi 93 FD - To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. - Designed by Jesus, built by Mazda - To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. 89 DTM PGT - Only To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. miles! - To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. Get Well Joe!

October 30th, 2009, 10:58 PM	#141
KLDE Wagon Supercharged Member Join Date: Aug 2006 Location: Binghamton, NY Age: 22 Posts: 1,200	Check it again douche-fag! True, but the fact of the matter is I have the chassis to do so... I'm not talking fast and the furious wheelies cause damn, who wants to not see a big rig pull out in front of you!! Jeremy __________________ To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. 05 Mazda 3s: lighting mods and wheels To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. : 3" body lift, 35's, cammed, full exhaust Back to terrorize with drift-eze... Eventually To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. Last edited by KLDE Wagon; October 30th, 2009 at 11:00 PM.

November 1st, 2009, 08:06 PM	#142
riithunder916 Juiced Member Join Date: Mar 2006 Location: West Greenwich RI Age: 22 Posts: 925	Nice!!! it sounds like a small block to me..... Mike __________________ 2004 Nissan Sentra Ser Spec-V ==> daily 1987 T-bird T-coupe ===> 2.3 Turbo charged project To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

November 2nd, 2009, 10:24 AM	#143
KLDE Wagon Supercharged Member Join Date: Aug 2006 Location: Binghamton, NY Age: 22 Posts: 1,200	Yeah, I would imagine so too. I just wish mine was as clean as that mines a rust bucket... Anyones grandma have a car like mine sitting in her garage? HAHA Jeremy __________________ To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. 05 Mazda 3s: lighting mods and wheels To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. : 3" body lift, 35's, cammed, full exhaust Back to terrorize with drift-eze... Eventually To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

November 9th, 2009, 09:13 AM	#144
KLDE Wagon Supercharged Member Join Date: Aug 2006 Location: Binghamton, NY Age: 22 Posts: 1,200	Garage is cleaned out (kinda). Enough to bring my car up and rip shit apart. I hope this wiring isn't too much of a nightmare. Jeremy __________________ To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. 05 Mazda 3s: lighting mods and wheels To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. : 3" body lift, 35's, cammed, full exhaust Back to terrorize with drift-eze... Eventually To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

November 9th, 2009, 09:25 AM	#145
riithunder916 Juiced Member Join Date: Mar 2006 Location: West Greenwich RI Age: 22 Posts: 925	LOL, well I hope it isn't to bad either!! wiring can be a Pain, but luckily in 85 things weren't too complicated!! __________________ 2004 Nissan Sentra Ser Spec-V ==> daily 1987 T-bird T-coupe ===> 2.3 Turbo charged project To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

November 9th, 2009, 09:29 AM	#146
KLDE Wagon Supercharged Member Join Date: Aug 2006 Location: Binghamton, NY Age: 22 Posts: 1,200	Exactly!! However I am rewiring the entire dash and essentially the whole car . Gonna be lots of head scratching but then again I had lots of that on my KL swap too Bought the stronger tensioner springs for the supercharger belts so when I up the boost they won't slip. The price was right and it was something I would eventually need and can use even running stock boost. I can't wait to take the dash all out, rip out the old motor and trans and start prepping to bolt the new one in!!! Jeremy __________________ To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. 05 Mazda 3s: lighting mods and wheels To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. : 3" body lift, 35's, cammed, full exhaust Back to terrorize with drift-eze... Eventually To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. Last edited by KLDE Wagon; November 9th, 2009 at 11:34 AM.

November 16th, 2009, 09:47 AM	#147
KLDE Wagon Supercharged Member Join Date: Aug 2006 Location: Binghamton, NY Age: 22 Posts: 1,200	The car is at my buddies, might start tearing into it this weekend I got a cherry picker too now but it needs some TLC. I need to get working on the dash wiring a bit before I worry too much about getting the stock motor out, so that's first. I discovered this morning that the headers I bought for $85 shipped are the $400 ones for the 3.8, and not Paceshitter Jeremy P.S. I did a line lock before pulling it into the garage too once I get his camera I'll post the one-wheel-wonder before video __________________ To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. 05 Mazda 3s: lighting mods and wheels To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. : 3" body lift, 35's, cammed, full exhaust Back to terrorize with drift-eze... Eventually To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

November 16th, 2009, 10:20 AM	#148
riithunder916 Juiced Member Join Date: Mar 2006 Location: West Greenwich RI Age: 22 Posts: 925	Nice!! I'm glad you got the good headers! Mike __________________ 2004 Nissan Sentra Ser Spec-V ==> daily 1987 T-bird T-coupe ===> 2.3 Turbo charged project To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

November 16th, 2009, 10:32 AM	#149
KLDE Wagon Supercharged Member Join Date: Aug 2006 Location: Binghamton, NY Age: 22 Posts: 1,200	They are a little beat up but IDC LOL if they sound good and make power that's all I care about!! I can't wait to get the damn thing running! Jeremy __________________ To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. 05 Mazda 3s: lighting mods and wheels To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. : 3" body lift, 35's, cammed, full exhaust Back to terrorize with drift-eze... Eventually To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

November 21st, 2009, 04:37 PM	#150
KLDE Wagon Supercharged Member Join Date: Aug 2006 Location: Binghamton, NY Age: 22 Posts: 1,200	Welp folks, it's been a while... Here are a couple of pics of the stock motor and of my hurst pistol grip shifter http://i793.photobucket.com/albums/y...s/IMG_0665.jpg 130HP of FURY!!! http://i793.photobucket.com/albums/y...s/IMG_0666.jpg http://i793.photobucket.com/albums/y...s/IMG_0667.jpg I'll try to get the video of this beast burning rubber from my buddy tomorrow Jeremy __________________ To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. 05 Mazda 3s: lighting mods and wheels To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. : 3" body lift, 35's, cammed, full exhaust Back to terrorize with drift-eze... Eventually To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.