List of forcefed cars (super/turbocharger driven)

[Roach]

Can anyone with one or in the process of putting it together put down their turbo as the A/R and any other essential info. Gracias

[ASword]

93 PGT, T04E A/R ~0.5 (not sure exactly)
External wastegate
DSM 1st gen BOV
Vortech FMU (12:1 currently)

Some changes in the wind, see my website for details.

[PGTRacer]

GN Stock Turbo (not sure about the specs)
TurboXS MBC
TurboXS BOV
12:1 vortech FMU
Autometer gauges

[BigProbe]

T3Super60 (I am thinking .82 AR..)
Deltagate w/ 8lb spring
Paxton 5:1 FMU
HKS Compressor Surge Valve

[mx3gsr]

Mitsubishi ported 16G (standard upgrade turbo for 1st gen talon)
stock internal wastegate (stock 7-8psi)
Cartech 12:1 ajustable FMU
Greddy Type-S BOV
autometer gauges (A/F, boost, fuel pressure)
starion intercooler
Walbro 255 intank pump.


_________________

[Manwuf]

Garrett T3/T4 0.63 Turbine A/R
Tial 35mm WG
Blitz BOV
Vortech 12:1 FMU
Walbro 255
Custom FMIC
Custom piping w/ Bosal headers



_________________
Manny Hardeo
'97 LR Probe GT MTX
'95 626 LX ATX
Can a brother just get his turbo?!?

[Mike Paszti]

Mitsubishi TD05H-16G (standard upgrade turbo for 1st gen talon)
Stock internal wastegate (stock 7-8psi)
T-Bird Turbo Coupe intercooler
'95 Eagle Talon BOV
12:1 Vortech non-adjustable FMU
190L/h Walbro pump
2 pressure switch activated '85 cold-start VW fuel injectors
MSD 6A ignition (coming soon: DIS ignition)
2.25" intake piping
2.5" downpipe
3" flex, cat, and exhaust

Mike

[FRCFD6]

heres the old setup
Garrett T3 .60/.48 with a 15 degree exhaust clip
95 DSM BOV
2.5 piping
2.5 inch downpipe, 3 inch flex pipe back ( just a couple glass packs in between)
cartech adjustable FMU
190LPH Walbro

[Chris Borchert]

On 2001-04-11 17:07, FRCFD6 wrote:
heres the old setup
Garrett T3 .60/.48 with a 15 degree exhaust clip
95 DSM BOV
2.5 piping
2.5 inch downpipe, 3 inch flex pipe back ( just a couple glass packs in between)
cartech adjustable FMU
190LPH Walbro

Yep, and I have it now He He He

Thanks, Raf
But I have the 255 LPH Walbro. It could be over kill, but who know where it might take me.

[Matrix]

My turbo project has passed the planning & conception stage, and is now entering the infancy stage. I have not decided on a few components at the moment, so the list may be incomplete. Well here goes:

Toyota CT-26 turbo (.67 AR) w/ internal wastegate set at ~6 psi (sourced from an MKIII Supra)
Holley 255 lph Fuel Pump
Paxton FPR
Looking for ~250 cc/min injectors

Any advice and/or input is appreciated...
-Later,

[BryanPendleton]

1996 2.0L Probe
Turbo: T3/T4 ceramic ball bearing turbo
T04E 46 trim comprossor
T3 .48 A/R Turbin Housing
Stage II Turbine Wheel
WG: Deltagate
Boost Controller: Greddy Profec-B
IC Spearco air-to-air Intercooler
Fueling: Walbro 190LPH, RC 440cc Injectors,
custom calibrated 75mm MAF.

[crazyprobe]

i'm allmost turbo'd but that doesn't count!!

i have a t3 turbo for a nissan 280zx but i think i'm ganna sell it and go with a hybrid

[hyc GTS]

Aerocharger Model 224
Geoff Knight 3" piping kit w/intercooler

[Lee 93redPGT]

-Garrett T-25 turbo. (T-2Small) really small trim.
-Stock DSM side mount intercooler with restrictive, plastic UIC pipes.
-Plastic 2G DSM BOV that vents any gained boost. (no more A'pexi)
-Stock fuel pump.
-Ripped off rear o2 sensor harness (and disconnected) causing an extra rich air/fuel mix.
-Really weak wastegate spring that starts to open at high rpm causing a loss of boost.

:grin: :grin: :grin: I got the big guns on this baby! :grin: :grin: :grin:

_________________
Turbo=Good

97 Talon TSi__A'pexi N1 exhaust__A'pexi BOV__Tenzo intake/springs__LuK clutch__Alpine CVA-1005
indash LCD__Custom 2-tone Leather__big bad subs__blah,blah,blah....

[SBPGT]

Starting my Turbo project:

Turbonetics T3Super60
GReddy BOV
Custom Turbo Headers
(?) FMU

All from a BLOWN Turbo PGT I found at a car dealership. $300 for all that and the core engine(free). :grin: