Announcement

Collapse
No announcement yet.

Tochigi Fuji Sangyo 2-way LSD

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Tochigi Fuji Sangyo 2-way LSD

    I finally got the rest of the parts I needed for my Tochigi Fuji Sangyo 2-way limited-slip diff! Got the two bearings and speedo gear, need to have them pressed in but it doesn't look like the speed-gear is going to pose a problem. (like some ppl said it would)

    Here are some pics as per request by a few of you:









    Last edited by Gro Harlem; May 28, 2004, 05:38 PM.
    Wil (admin iMazda.com) 93' MX-ZE
    Mods: ZE w/31 cams & curved-neck mani, 67mm t/b, obx headers w/2.5" straight-thru, 3" custom CAI,
    Mazdaspeed mounts, Tochigi Fuji Sangyo 2-way LSD, ACT clutch, Noble Green Metallic paint, E-spec headlights,
    OEM skirts, 16" SubZeros on Azenis, Tokico w/Eibach's, Mazdaspeed TTL & Bushing Kit, New OEM Leather seats & SE interior

    READ THE HEADER FAQ OR DO A SEARCH

  • #2
    Obligatory "Where'd you get it from?" question....


    Looks good
    90 Mazda 323 - KLZE, fender-flared, right hand drive, 2350 lb fully loaded sex machine. || Pic Thread ||- SOLD
    93 PGT FRANKENPROBE - 10.24 @ 139.9 mph ||545 whp @ 20 psi || Timeslip || Dyno slip|| Build Thread - GONE
    97 GTS - Rear Wheel Drive KLZE, 6-speed, 3.90 Torsen LSD, 2650 lb, daily driver! - Build Thread - GONE
    90 Ghettocet KLiata - forever WIP

    Comment


    • #3
      I believe it comes from the mazdaspeed protege..
      could be wrong though..
      looks sweet.. Cheaper then the quaife lsd too..
      I wonder how this one will hold up though.. ?

      Comment


      • #4
        should hold up as well as a quaife.....tochigi supplies the SRT-4 and WRX with their factory LSD's as well among other cars.

        Got it from Mazda direct, they overnighted it via FedEx for free for some reason even tho I ordered ground
        Last edited by Gro Harlem; May 28, 2004, 05:39 PM.
        Wil (admin iMazda.com) 93' MX-ZE
        Mods: ZE w/31 cams & curved-neck mani, 67mm t/b, obx headers w/2.5" straight-thru, 3" custom CAI,
        Mazdaspeed mounts, Tochigi Fuji Sangyo 2-way LSD, ACT clutch, Noble Green Metallic paint, E-spec headlights,
        OEM skirts, 16" SubZeros on Azenis, Tokico w/Eibach's, Mazdaspeed TTL & Bushing Kit, New OEM Leather seats & SE interior

        READ THE HEADER FAQ OR DO A SEARCH

        Comment


        • #5
          nice find, i'm sure a lot of people will be very intersted in how all of this goes.

          Comment


          • #6
            so if this works in 626 tranny, can it work in probe gt tranny? for that matter a 1g one?

            Comment


            • #7
              Very possible! I plan on fitting one into a 1st gen gt mtx

              Comment


              • #8
                Originally posted by FLAPOC-Pres
                Very possible! I plan on fitting one into a 1st gen gt mtx
                PLEASE if you do, do a complete writeup of how you do this. quafie lsd's arnt cheap! itd be nice to have a cheaper solution to the tq. issue in 1st gen GTs.

                Comment


                • #9
                  Originally posted by Da-ze
                  I believe it comes from the mazdaspeed protege..
                  could be wrong though..
                  looks sweet.. Cheaper then the quaife lsd too..
                  I wonder how this one will hold up though.. ?

                  Thats the what I got in my msp
                  Matt Knudsen
                  2010 Colorado 5.3L V8
                  2009 Yamaha R6r

                  Comment


                  • #10
                    looks hot
                    NCPOC > BAPOC > SCPOC > FlaPOC > MIPOC

                    Comment


                    • #11
                      Originally posted by FLAPOC-Pres
                      Very possible! I plan on fitting one into a 1st gen gt mtx
                      let me know if you're successful....would be a nice addition in my partsbin hehe
                      Life isn't like a bowl of cherries or peaches, it's more like a jar of Jalapenos ....
                      What you do today, might burn your ass tomorrow.

                      Pearl '92 Audi //S4 GT3071R, running 27 psi
                      Lava gray '14 Audi //SQ5, Chipwerke, 034 Intake Pipe
                      For PSP Awareness click here

                      Comment


                      • #12
                        i don't have a clue about 1st gen probes so I wouldn't know.

                        If they are G-series mazda transmissions then yes, otherwise, no.
                        Wil (admin iMazda.com) 93' MX-ZE
                        Mods: ZE w/31 cams & curved-neck mani, 67mm t/b, obx headers w/2.5" straight-thru, 3" custom CAI,
                        Mazdaspeed mounts, Tochigi Fuji Sangyo 2-way LSD, ACT clutch, Noble Green Metallic paint, E-spec headlights,
                        OEM skirts, 16" SubZeros on Azenis, Tokico w/Eibach's, Mazdaspeed TTL & Bushing Kit, New OEM Leather seats & SE interior

                        READ THE HEADER FAQ OR DO A SEARCH

                        Comment


                        • #13
                          that's *****ing excellent.
                          Greg Martin
                          2009 BMW 328i
                          2017 BMW X3
                          1990 Probe LX

                          Comment


                          • #14
                            I am surprised alot of you guys didn't know this was a drop in for 2nd gen mtx trannies

                            Comment


                            • #15
                              Here is the part number if any one is interested #GS01-27-190A
                              FYI: 1st gen Gt (possibly the lx v6) MTX trannies are H-type trannies, stronger then G-types, so it might or might not work for that tranny, now 1st gen GL & LX 4 cylinder mtx's are G-types and this could be a drop in for them, I'l find out eventually since i have both types sitting around.
                              Last edited by FLAPOC-Pres; May 26, 2004, 06:21 PM.

                              Comment

                              Working...
                              X