Compilation Part3
"Donated for 2G PGT applications (implied 2G Probe 626 MX-6 where applicable)"
What: 2nd Gen clutch line is same as 1st gen, interchangable
Donor Car:
Modification required:
Why:
What: Clutch line is also interchangable with 1994*Ford Escort*lines (g-Series tranny only?)
Donor Car:
Modification required:
Why:
What: Brake line*from 1985 Buick Century fits 2nd gen Probe (MX6/626 implied; less expensive)
Donor Car:
Modification required:
Why:
What: 2000 626 Rear Sway Bar fits 2nd gen Probe Chassis with replacement bushings
Donor Car:
Modification required:
Why: http://forums.probetalk.com/showthre...hlight=swaybar
What: 1995*Nissan Altima*Endlinks fit 2nd gen chassis and are better made & less expensive
Donor Car:
Modification required:
Why:
What: GM fin type door clips fit 93-94*door panels
Donor Car:
Modification required:
Why:
What: Inner Door Panel Fasteners or clips for 1998-2001*Ford Explorer*fit Sideskirts on 2nd gen Probe
Donor Car:
Modification required:
Why:
What: Early 80s Buick/GM 1-wire*Oxygen sensor*replaces 3-4 wire sensors without throwing a CEL (less expensive)
Donor Car:
Modification required:
Why:
What: Mazdaspeed Protege LSD diff fits g-series 2nd gen transaxle
Donor Car:
Modification required:
Why:
What: Chrome centercaps for a*mazda RX8 fits*the chrome swirlies perfectly (Part number L082-37-192)
Donor Car:
Modification required:
Why:
What: Front rotors from*1993-2003 Protege*fits 2nd gen Probe (MX6/626 implied)
Donor Car:
Modification required:
Why:
What: 1999-2003 Protege*coilovers/struts fit 2nd gen Probe (MX6/626 implied) TEIN, B&G, K-Sport, JIC Magic
Donor Car:
Modification required:
Why:
What: Civic STS can be forced to fit 2nd gen Probe (MX6/626 implied)
Donor Car:
Modification required:
Why:
What: Prelude intake*can be cut in half and fits 2nd Gen PGT (MX6/626 possibly implied)
Donor Car:
Modification required:
Why:
What: Porsche 911*Carrera*brake calipers*fit 2nd gent Probe (MX6/626 Implied)
Donor Car:
Modification required:
Why:
What: Escort front upper*strut mount*fits 2nd gen Probe (MX6/626 implied; 5/8" lower drop) Front is the only end interchangable.*Rear are not.
Donor Car:
Modification required:
Why:
---------- Post added at 11:56 PM ---------- Previous post was at 11:55 PM ----------
What: 2nd gen front upper strut mounts fit 1st gen Probe (MX6/626 implied; lower drop)
Donor Car:
Modification required:
Why:
What: 2nd gen Probe*A-pillar gauge pod*fits 1st gen Probe
Donor Car:
Modification required:
Why:
What: 1st Gen MX6 seats and 1st Gen Probe seats are interchangable
Donor Car:
Modification required:
Why:
What: RX7*steering wheel*fits 1st gen Probe
Donor Car:
Modification required:
Why:
What: Mustang leather shift boot fits 1st gen Probe
Donor Car:
Modification required:
Why:
What: 1st gen MX6 factory RSTB fits 1st gen Probe
Donor Car:
Modification required:
Why:
What: 1st get MX6 factory lower tie bar fits 1st gen Probe
Donor Car:
Modification required:
Why:
What: G-Series Escort transmission internals fit 2nd gen G-series gearbox (stronger components upgrade)
Donor Car:
Modification required:
Why:
What: Millenia-S injectors & rails fit 2.5L V6 KLDE (60cc more than stock)
Donor Car:
Modification required:
Why:
What: Millenia curved neck ZE*intake manifold*fits 2.5L V6 KLDE (more airflow)
Donor Car:
Modification required:
Why:
What: 1998 Millenia PCM will run a 1996+ 2.5L V6 KLDE w/ATX (MAF conversion)
Donor Car:
Modification required:
Why:
What: 1.8K8, 2.0FS, 2.5KL and 2.5ZE, ATX & MTX can all be swapped around between 2nd gen vehicles with matching mounting hardware, axles, etc.
Donor Car:
Modification required:
Why:
What: Alloy and*steel rims*from all models & years are interchangable (GT rims & tires significantly improve handling of base models over 14" steelies)
Donor Car:
Modification required:
Why:
What: A 1993 Corvette ZR1*oil filter*will increase your 2.5KL's oil pressure and oil holding capacity
Donor Car:
Modification required:
Why:
What: Swap out front calipers for the 91 3000gt vr4 4piston calipers and 11.9" rotors cost a total of like $300:*http://mnpoc.org/forum/showpost.php?p=89178
Donor Car:
Modification required:
Why:
What: Clutches are the same between the 1st gen 2.2 non turbo, and the 2nd gen 2.5 v6.
Donor Car:
Modification required:
Why:
What: The 1st gen 2.2 turbo clutch is the same as the*89-92 rx7*turbo clutch, however the*pressure plate*is different.
Donor Car:
Modification required:
Why:
What: Acura tsx*(mtx, same as newer TL's) rubber boots/sleves that go on the clutch and break pedals & they do fit on the pgt mtx pedals...
Donor Car:
Modification required:
Why:
What: Cobra 13 inch vented rotors will fit 2nd Gen PGTs with minor modification.Porsche Brembo Monoblock Radial Mount caliper can be very easily adapted to match on the PGT. With this setup though you need some very big rims. 19 inch rims will fit with stock struts and springs and same diameter tires.
Donor Car:
Modification required: Centric hole needs to be opened just a small amount. Bolt pattern is the same.
Why:
What: The Mazda MPV 2 pot calipers may fit with no or little modification. I was reading the thread at work so I do not remember it so clearly. But another brake option for the Probe.
Donor Car:
Modification required:
Why:
"Donated for 2G PGT applications (implied 2G Probe 626 MX-6 where applicable)"
What: 2nd Gen clutch line is same as 1st gen, interchangable
Donor Car:
Modification required:
Why:
What: Clutch line is also interchangable with 1994*Ford Escort*lines (g-Series tranny only?)
Donor Car:
Modification required:
Why:
What: Brake line*from 1985 Buick Century fits 2nd gen Probe (MX6/626 implied; less expensive)
Donor Car:
Modification required:
Why:
What: 2000 626 Rear Sway Bar fits 2nd gen Probe Chassis with replacement bushings
Donor Car:
Modification required:
Why: http://forums.probetalk.com/showthre...hlight=swaybar
What: 1995*Nissan Altima*Endlinks fit 2nd gen chassis and are better made & less expensive
Donor Car:
Modification required:
Why:
What: GM fin type door clips fit 93-94*door panels
Donor Car:
Modification required:
Why:
What: Inner Door Panel Fasteners or clips for 1998-2001*Ford Explorer*fit Sideskirts on 2nd gen Probe
Donor Car:
Modification required:
Why:
What: Early 80s Buick/GM 1-wire*Oxygen sensor*replaces 3-4 wire sensors without throwing a CEL (less expensive)
Donor Car:
Modification required:
Why:
What: Mazdaspeed Protege LSD diff fits g-series 2nd gen transaxle
Donor Car:
Modification required:
Why:
What: Chrome centercaps for a*mazda RX8 fits*the chrome swirlies perfectly (Part number L082-37-192)
Donor Car:
Modification required:
Why:
What: Front rotors from*1993-2003 Protege*fits 2nd gen Probe (MX6/626 implied)
Donor Car:
Modification required:
Why:
What: 1999-2003 Protege*coilovers/struts fit 2nd gen Probe (MX6/626 implied) TEIN, B&G, K-Sport, JIC Magic
Donor Car:
Modification required:
Why:
What: Civic STS can be forced to fit 2nd gen Probe (MX6/626 implied)
Donor Car:
Modification required:
Why:
What: Prelude intake*can be cut in half and fits 2nd Gen PGT (MX6/626 possibly implied)
Donor Car:
Modification required:
Why:
What: Porsche 911*Carrera*brake calipers*fit 2nd gent Probe (MX6/626 Implied)
Donor Car:
Modification required:
Why:
What: Escort front upper*strut mount*fits 2nd gen Probe (MX6/626 implied; 5/8" lower drop) Front is the only end interchangable.*Rear are not.
Donor Car:
Modification required:
Why:
---------- Post added at 11:56 PM ---------- Previous post was at 11:55 PM ----------
What: 2nd gen front upper strut mounts fit 1st gen Probe (MX6/626 implied; lower drop)
Donor Car:
Modification required:
Why:
What: 2nd gen Probe*A-pillar gauge pod*fits 1st gen Probe
Donor Car:
Modification required:
Why:
What: 1st Gen MX6 seats and 1st Gen Probe seats are interchangable
Donor Car:
Modification required:
Why:
What: RX7*steering wheel*fits 1st gen Probe
Donor Car:
Modification required:
Why:
What: Mustang leather shift boot fits 1st gen Probe
Donor Car:
Modification required:
Why:
What: 1st gen MX6 factory RSTB fits 1st gen Probe
Donor Car:
Modification required:
Why:
What: 1st get MX6 factory lower tie bar fits 1st gen Probe
Donor Car:
Modification required:
Why:
What: G-Series Escort transmission internals fit 2nd gen G-series gearbox (stronger components upgrade)
Donor Car:
Modification required:
Why:
What: Millenia-S injectors & rails fit 2.5L V6 KLDE (60cc more than stock)
Donor Car:
Modification required:
Why:
What: Millenia curved neck ZE*intake manifold*fits 2.5L V6 KLDE (more airflow)
Donor Car:
Modification required:
Why:
What: 1998 Millenia PCM will run a 1996+ 2.5L V6 KLDE w/ATX (MAF conversion)
Donor Car:
Modification required:
Why:
What: 1.8K8, 2.0FS, 2.5KL and 2.5ZE, ATX & MTX can all be swapped around between 2nd gen vehicles with matching mounting hardware, axles, etc.
Donor Car:
Modification required:
Why:
What: Alloy and*steel rims*from all models & years are interchangable (GT rims & tires significantly improve handling of base models over 14" steelies)
Donor Car:
Modification required:
Why:
What: A 1993 Corvette ZR1*oil filter*will increase your 2.5KL's oil pressure and oil holding capacity
Donor Car:
Modification required:
Why:
What: Swap out front calipers for the 91 3000gt vr4 4piston calipers and 11.9" rotors cost a total of like $300:*http://mnpoc.org/forum/showpost.php?p=89178
Donor Car:
Modification required:
Why:
What: Clutches are the same between the 1st gen 2.2 non turbo, and the 2nd gen 2.5 v6.
Donor Car:
Modification required:
Why:
What: The 1st gen 2.2 turbo clutch is the same as the*89-92 rx7*turbo clutch, however the*pressure plate*is different.
Donor Car:
Modification required:
Why:
What: Acura tsx*(mtx, same as newer TL's) rubber boots/sleves that go on the clutch and break pedals & they do fit on the pgt mtx pedals...
Donor Car:
Modification required:
Why:
What: Cobra 13 inch vented rotors will fit 2nd Gen PGTs with minor modification.Porsche Brembo Monoblock Radial Mount caliper can be very easily adapted to match on the PGT. With this setup though you need some very big rims. 19 inch rims will fit with stock struts and springs and same diameter tires.
Donor Car:
Modification required: Centric hole needs to be opened just a small amount. Bolt pattern is the same.
Why:
What: The Mazda MPV 2 pot calipers may fit with no or little modification. I was reading the thread at work so I do not remember it so clearly. But another brake option for the Probe.
Donor Car:
Modification required:
Why:
Comment